TheDIYGuy999
Autor
JaSind das solche Rundumleuchten
JaSind das solche Rundumleuchten
Siehe (Seite 8):Ich habe die Vorwiderstände falsch berechnet
Einfach in der gewünschten "Vehicle" Datei beim nicht gewünschten Horn // vorne dran schreiben, beim gewünschten entfernen.Als erstes wäre ich schonmal froh wenn ich das "Schweizer-Horn" gegen ein Martinshorn der Feuerwehr tauschen könnte.
Ich hab den 1863 genommen.Ist der 1863 oder 3363 include in Actros 1838?
I really like this solution!Here is my version of a compact wireless trailer card.
The sidelights on the truck are working? Note, that they can't be used in combination with "#define SPI_DASHBOARD"but I cannot get the side light (#define SIDELIGHT_PIN 18) to come on...
Hello Norbert,Hello Frikkie,
your hardware for wireless trailer light looks good. If i would by the following components they would be ok?
0.46€ 70% OFF|10PCS ULN2003A SOP16 ULN2003ADR ULN2003 2003 SOP 16 SMD Neue und Original IC Chipset|Integrierte Schaltkreise| - AliExpress
Smarter Shopping, Better Living! Aliexpress.comde.aliexpress.com
3.25€ 18% OFF|50PCS L7805CV L7805 7805 LM7805 Spannung Regler 5 V ZU 220|regulator 5v|voltage regulator5v regulator - AliExpress
Smarter Shopping, Better Living! Aliexpress.comde.aliexpress.com
Kindly regards
Norbert
Sorry...again me and the instructions! I tested the Dashboard LCD once to see if it works, but have been running both my trucks on V7.6 and forgot about the Dashboard/sidelights again!I really like this solution!
The sidelights on the truck are working? Note, that they can't be used in combination with "#define SPI_DASHBOARD"
Thanks for the schematic. You really should show us your trucks in the "LKW" (LastKraftWagen = Truck) section! I think many people would like to see your articulating cattle trailer. They are very uncommon in Europe.All working 100%
Hi Martin, the moment it is done I will put it up...time is the problem...and my daughter's cat jumped on the desk and the last side I was working on fell on the floor and now I have to redo it :-(Thanks for the schematic. You really should show us your trucks in the "LKW" (LastKraftWagen = Truck) section! I think many people would like to see your articulating cattle trailer. They are very uncommon in Europe.
The build progress is interesting as well, but time is always a problem, I know that.the moment it is done I will put it up
That sucks!and my daughter's cat jumped on the desk and the last side I was working on fell on the floor and now I have to redo it :-(
siehe Fahrzeugdatei:Nur die Sache mit dem Automatikgetriebe habe ich noch nicht herausgefunden.
Hi Norbert,Hello Frikkie,
thanks for your answer. If i make like this i not only can use one LED per PIN.
Is D17 = TX2? TX2 is on my ESP32 where your D17.
Regards
Norbert
The build progress is interesting as well, but time is always a problem, I know that.
I wanted to make a video now only with the front trailer...but ran into a problem. I have tried V8.3 and V8.4 and have the same problem the moment I uncomment "#define WIRELESS_TRAILER". My truck does not want to rev up and the jake brake also does not function. On both V8.3 and V8.4 if I put the "//" in front of the #define WIRELESS_TRAILER the truck runs normally. The wireless trailer lights works 100%...just the truck does not want to rev up.
Regards,
Frikkie