tommy1992bk
Mitglied
This parameter is default defined and i do not change it.Keep this parameter in mind:
Den Anhang 139943 betrachten
This parameter is default defined and i do not change it.Keep this parameter in mind:
Den Anhang 139943 betrachten
Ist the #define MODE2_TRAILER_UNLOCKING option inside your active configuration?This parameter is default defined and i do not change it.
Now i change the actived servo option from servo_default to servo_king hauler and i can move the servo by the key assign in ch9 but still the servo only have 2 positions- lock and unlock. To function the motorized legs you need one more position to push the switch in the trailer side.Ist the #define MODE2_TRAILER_UNLOCKING option inside your active configuration?
For example:
//#define OTHER_SERVOS
...
#define MY_SERVOS
..
#ifdef MY_SERVOS
#define MODE2_TRAILER_UNLOCKING
...
#endif
What happens when you push/switch the MODE2 button?
Is your unlocking servo connected to CH4 (GPIO27)?
At the moment the software does not cater for this. What you require is a 3rd value for the servo to operate the switch unit on the trailer.Now i change the actived servo option from servo_default to servo_king hauler and i can move the servo by the key assign in ch9 but still the servo only have 2 positions- lock and unlock. To function the motorized legs you need one more position to push the switch in the trailer side.
that means i need to give up the motorized legs.At the moment the software does not cater for this. What you require is a 3rd value for the servo to operate the switch unit on the trailer.
I have removed push rod from my 5th wheel and entire switch unit from my trailer. I added another small ESC to the trailer, connected the motorized legs to the ESC and I am operating the legs from the wireless trailer card CH1 using Pot2 (VrB) while the 5th wheel servo is unlocked.
Den Anhang 140144 betrachten
Are you going to use the trailer card? Then you can use the ESC solution I mentioned above.that means i need to give up the motorized legs.
Not as far as I know....normally SwC for shifting.Another question: can i use the left stick horizon to shift like the tamiya mfc unit, in bus mode?
I dont know how to assemble the wireless trailer…do i need one more esp32 board on trailer?Are you going to use the trailer card? Then you can use the ESC solution I mentioned above.
Not as far as I know....normally SwC for shifting.
Yes, you need one more board. The board requires less components (no PAM8403 or the 20K Pot), and you also do not need to solder all the header pins, only what is required for the trailer.I dont know how to assemble the wireless trailer…do i need one more esp32 board on trailer?
How will you mount the board and esc on the trailer?Yes, you need one more board. The board requires less components (no PAM8403 or the 20K Pot), and you also do not need to solder all the header pins, only what is required for the trailer.
Green board is the older version SMD for that I used for the trailer and the white is the latest version SMD for the truck. (but you can used any combination of board versions)
Den Anhang 140182 betrachten
What type of trailer do you have? One the Tamiya Box trailer I am mounting everything between the rails.How will you mount the board and esc on the trailer?
Traditional semi trailer (intercontinental express), but i do not have 3d printer to do the case of the board. Is the wireless trailer stable? In case of playing outdoor and big meetings (a lot of RCs playing together). Can you show me the full assembly( in schematic is ok)?What type of trailer do you have? One the Tamiya Box trailer I am mounting everything between the rails.
It looks like this:Hi Everyone
Does anyone have a diagram for where to solder the100K/20K resistor for battery monitoring
im not 100% sure where they go. i have been reading everywhere in the forum.
thank you
Thank you for the quick help -It looks like this:
GND (BATTERY-) -------[ 20 kΩ ]------- GPIO 39 (VN) ------[ 100 kΩ ]------ BATTERY+
GPIO39 is also labeled "VN", it's the third one from the right (being "EN" the upper rightmost, USB-Port facing to the left).
Den Anhang 140519 betrachten
(Ignore the capacitor and the resistor reference numbers, since it's from a different board.)
Na verdade queria fazer um vídeo, mas talvez venha depois...
Agora também testei o Tamiya Scania R470 corretamente (aceleração total na subida na marcha mais alta) e posso utilizar totalmente e confirmar que o driver do motor RZ7886 no motor 540 80T fica apenas um pouco quente (apesar das temperaturas externas). É tão econômico o ESC externo completo e, além dos servos e do receptor, não há outros componentes eletrônicos.
[Anexar]140595[/Anexar] [Anexar]140597[/Anexar]
A placa que estou usando aqui foi realmente destinada a otimizadores (ainda é mas para mim é suficiente para um caminhão já que não quero instalar um painel shaker (e, portanto, também não há conexão para eles ). são fornecidos). Também faltam as luzes laterais, balizas e os GPIOs fornecidos ou não são trazidos).
Conseguir deixar o painel em si e os assentos, apesar dos alto-falantes e da placa de circuito. Claro que poderia ser projetado de tal forma que você não pudesse vê-lo através dos painéis, mas isso realmente não me incomoda.
Netter Arbeitsfreund! Ich zerbreche mir immer noch den Kopf und versuche, einen Weg zu finden, die Karte zu installieren und das Innere meines R620 zu belassen ... Ich nehme Tipps und Vorschläge an.